We solve electrical faults, copper leaks, and structural framing with direct tradesman rates.
General contracting trades across Memphis, Jackson, Shelby, and Madison counties. We bill standard repairs at $36 to $59 per hour, and urgent after-hours emergency dispatches at $65 to $95 per hour. No retail franchise markups. You deal directly with owner-operator A.J. Eubanks.
Residential plumbing repairs, copper soldering, and shut-off replacements.
Plumbing problems in older Memphis properties usually begin where original galvanized iron connects to modern copper or CPVC lines. Electrolysis erodes threads, solder joints fatigue under water hammer, and old multi-turn gate valves seize in half-open positions. When a supply line leaks behind drywall or beneath a crawlspace, we cut out the degraded pipe section cleanly with rigid tubing cutters, ream the burrs, brush on lead-free water-soluble flux, and sweat thick-walled Type L copper fittings with a controlled propane flame.
We do not rely on push-fit plastic couplings for permanent concealed installations inside walls. We braze or solder metal-to-metal joints, install quarter-turn brass ball valves with stainless steel balls, and pressure-test the circuit before closing the access panel. For supply repiping in tight attic chases or crawlspaces, we install cross-linked polyethylene PEX-A with expansion rings rated for 160 psi at 73 degrees Fahrenheit.
Our plumbing service covers kitchen faucet rebuilds, disposal installations, toilet flange leveling, cartridge replacements for Moen, Delta, and Kohler valves, water heater drain flushes, and emergency shut-off restorations. You receive honest labor billed at $36 to $59 per hour during standard appointments, with replacement valves and fittings charged at supplier cost.
Circuit breaker diagnostics, breaker replacement, and branch wiring.
Electrical troubleshooting requires systematic meter testing rather than guessing at wire nuts. When a circuit breaker trips repeatedly or lights flicker when the microwave cycles, we open the deadfront panel, inspect the neutral bar for thermal discoloration, and hook up a digital multimeter to measure supply voltage, load amperage, and phase balance.
Common residential failures in Shelby County include loose screw terminals on 15-amp and 20-amp duplex receptacles, corroded aluminum-to-copper pigtails in mid-century construction, and overloaded branch circuits carrying modern high-draw appliances. We replace worn thermal-magnetic breakers, isolate ground faults, install GFCI and AFCI breakers to current National Electrical Code safety standards, and run dedicated 12/2 Romex circuits for dedicated kitchen, garage, or workshop equipment.
Emergency electrical faults such as arcing bus bars, burning switch boxes, or total loss of power to mechanical systems carry priority dispatch at $65 to $95 per hour. We verify zero-energy states with non-contact testers and multimeters before touching conductor copper, ensuring strict safety on every job site.
Trim carpentry, drywall patch, and structural rot repair.
Settling foundations and humid Mid-South weather take a heavy toll on interior finishes. Door frames drag against jambs, subflooring under bathroom toilets rots from slow wax-ring seepages, and drywall seams crack along exterior lintels. A.J. Eubanks brings generational woodworking skills to every residential framing and trim project.
When framing members suffer dry rot or termite damage, we do not cover bad wood with decorative trim. We support structural loads with temporary screw jacks, cut away compromised lumber back to clean timber, and sister new kiln-dried dimensional framing with lag screws and structural adhesives. For wall finishes, we feather drywall mud across three distinct coats, tape corners with high-strength paper, and sand to Level 4 smooth finish ready for primer.
Exterior carpentry services include fascia board replacement, rot remediation around window sills, storm door hanging, porch step reinforcement, and deadbolt alignment. Every door we hang is checked with a 6-foot aluminum box level to guarantee uniform reveal margins.
Verified trade labor rates for Memphis and Jackson jobs.
We believe in direct, upfront math. We charge for real time on site and replacement materials at cost, or provide an all-inclusive binding labor estimate before work begins.
| Trade Scope | Price Basis | Rate | Included Work & Equipment |
|---|---|---|---|
| Memphis Handyman Labor | Hourly rate, standard schedule | $36–$59 / hr | Plumbing leak repair, fixture swaps, drywall patching, door hanging, subfloor fixes, trim woodwork. |
| Emergency Handyman Labor | Hourly rate, urgent/after-hours | $65–$95 / hr | Burst pipe isolation, temporary roof tarping, emergency breaker diagnosis, urgent structural boarding. |
| HVAC Diagnostic Inspection | Flat callout dispatch fee | $89–$129 per callout | Gauge hookup, electrical winding testing, subcooling/superheat verification, complete component report. |
| HVAC Mechanical Repair | Fixed labor schedule + parts | $150–$650 labor | Capacitor replacement, blower motors, contactors, control boards, reversing valves, TXV replacements. |
| Emergency HVAC Callout | Priority dispatch charge | $100–$350 per callout | Night, weekend, and freezing-weather dispatch for total loss of heating or critical AC failure. |
| Emergency HVAC Labor | Hourly emergency trade rate | $70–$400 / hr | Brazing, compressor troubleshooting, refrigerant recovery, and urgent system restoration. |
Quotes depend directly on: time of day, urgency, specific trade scope, repair complexity, and physical access constraints. We do not bill travel surcharges within our core Memphis and Jackson service areas.
How our trade dispatch process works.
Four transparent steps from your initial phone call or website inquiry to the completed job walk-through.
Direct Scope Evaluation
No Call Centers
You speak directly with tradesman A.J. Eubanks or submit job photos online. We review the physical fault, verify whether it falls under standard ($36–$59/hr) or emergency ($65–$95/hr) billing, and schedule your appointment window.
On-Site Inspection & Estimate
Clear Price Written Out
We arrive with fully stocked trade tools, test electrical continuity, trace plumbing lines, or check framing level. You receive a firm labor total and parts breakdown before any pipe is cut or wire stripped.
Code-Compliant Execution
Professional Craftsmanship
We install commercial-grade materials: soldered copper, heavy-gauge Romex, commercial ball valves, or structural lumber. Work proceeds cleanly with drop cloths protecting your living spaces.
Testing & Final Sign-Off
Demonstrated Quality
We pressure-test pipes under full municipal load, test circuits with multimeters, cycle appliances, and walk you through every finished detail. All trade labor is backed by our full workmanship warranty.
Straight answers to common trade questions.
We operate on plain facts. Here is what we do, what we refuse to do, and how our billing works in practice.
No. For scheduled trade jobs within our standard Memphis and Jackson service territory, travel time is included. You are billed purely for active labor on site at our verified $36 to $59 per hour rate, plus replacement parts at invoice cost.
We do not perform complete roof replacements, whole-home foundation underpinning, or dangerous tree felling over power lines. We focus strictly on mechanical HVAC, residential electrical wiring, copper/PEX plumbing repairs, drywall patching, and structural trim framing.
Yes. Many homeowners prefer picking out their own vanity faucets, pendant lights, or smart thermostats. We will inspect your supplied materials for compatibility, install them securely to code, and bill only for our standard hourly trade labor.
Urgent safety calls are routed through our emergency dispatch line at (901) 830-9987. For burst lines or dangerous electrical shorts, we dispatch an equipped service vehicle within two hours across Memphis and Shelby County under our emergency rate of $65 to $95 per hour.
Schedule trade service or request an estimate.
Submit your project details below. A.J. Eubanks reviews every inquiry directly and contacts you with an honest labor estimate or scheduled arrival time.